Showing results: 346 - 360 of 523 items found.
-
MFG-8203 -
MCH Instruments Co.,Ltd.
Features:*Low distortion, high stability*Linear and logarithmic sweep function*Sweep time and width adjustable*External voltage control frequency (VCF)*Internal& external modulation AM/FM with modulation control*Output signal compatible with TTL/CMOS*Seven types of waveforms such as sine, square, triangle and ramp*DC power output attenuation can be applied to main output signal*Built-in frequency meter:0.1Hz-30Mhz
-
Frequency Meter -
ZETLAB Company
Frequency Meter is used for measuring the frequency of the signal coming to the input channels of ADC modules and FFT spectrum analyzers. The indicator displays the measured frequency value (frequency of periodic oscillations) and signal cycle time corresponding to the measured frequency. It is possible to change the averaging of the displayed value (0.1; 1, or 10 s) and to select a necessary channel of the ADC module, FFT spectrum analyzer or a virtual channel.
-
Shenzhen Tojoin Communication Technology Co., Ltd.
Attenuators are used in a wide variety of applications and can satisfy almost any requirement where a reduction in power is needed. Attenuators are used to extend the dynamic range of devices such as power meters and amplifiers, reduce signal levels to detectors, match circuits and are used daily in lab applications to aid in product design. Attenuators are also used to balance out transmission lines that otherwise would have unequal signal levels.
-
FLIR CM94 -
Teledyne FLIR
The FLIR CM94 tackles high-current measurements on demanding utility and industrial job sites. This rugged meter securely clamps larger conductors with an oversized jaw so you can take readings up to 2000 A AC & DC. With a CAT IV-1000 V safety rating, the CM94 is ready to work on overhead, underground and utility service equipment. Plus, it offers VFD mode to tackle noisy signal environments. The full-featured FLIR CM94 utility clamp meter delivers results for utility and industrial electricians.
-
LV 5381 -
Leader Electronics Corp.
The LV 5381 is a waveform monitor that can monitor up to four SDI signals simultaneously.It is optimized for the level adjustment of the outputs of multiple installed cameras. In the video signal waveform display, vector display, and picture display, multiple input signals can be displayed on top of each other or lined up next to each other.It is also full of useful features such as a level meter display for embedded audio, an error display that indicates transmission errors, and a 5-bar display that shows video signal peak levels using five bars. Furthermore, the LV 5381 can show different combinations of these displays in its multi-screen display.
-
Power-1410 -
Quantifi Photonics Inc.
Quantifi Photonics’ Power-1410 optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 1250 to 1650 nm. It provides unrivalled channel density with up to 288 parallel channels in a single 1U rack-mountable instrument.
-
DG4000 Series -
Rigol Technologies Inc.
DG4000 series multi-function signal generator with functions of function generator, arbitrary waveform generator, pulse generator, harmonic generator, analog / digital modulator, frequency meter, etc.; all models of this series have two channels with identical functions and phase adjustable between channels.
-
MC142 -
Powertek LLC
Multifunction calibrator MC142 is a precision voltage, current and power calibration source serving as a measurement standard in calibration laboratories and production lines; where verification of electrical measurement equipment & sensors is required. It can be used for calibration and adjustment of meters measuring voltage, current, power, resistance, capacitance and frequency. Internal harmonic and non-harmonic signals make it possible to test electrical performance of meters using signals with various crest factors. Frequency modes enable selection of frequency, amplitude and duty cycle of the output signal. These are suitable for basic calibration of digital and analog oscilloscopes along with transient recorders. The calibrator is equipped to measure temperature with TC and RTD temperature sensors. Its built-in multimeter can be used independently or simultaneously with the calibrator output. Testing of transducers of various types, regulators and sensors can be performed, without the necessity to use any other measuring instrument.
-
MS 1719 -
Meltronics Systemtech
PCI Express to CPCI card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit cPCI signals from/to the Host System. These cPCI signals are converted into PCI Express using cPCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
MS 1718 -
Meltronics Systemtech
PCI to PCI Express card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit PCI signals from/to the Host System. These PCI signals are converted into PCI Express using PCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
Berkeley Varitronics Systems, Inc.
Handheld installation receivers for realtime 3G and 4G RSSI and RSRP signal strength of nearby wireless carrier base stations for M2M & IoT site surveys and antenna alignment for smart meters, EV charging stations, vending machines, wireless kiosks, digital signage, ATMs and more.
-
SY020 -
Synectic Electronics
The SY020 Pulse Rate Converter can be linked to any frequency generating device e.g. flow meters, which gives TTL, pulse Reed switch or coil output, converting the frequency to an analogue signal. This can be 4-20mA loop current or a voltage output. The 4-20mA version unit is loop powered.
-
TS-2800 -
Ono Sokki
The TS-2800 is a torque meter for phase difference type torque detectors. Can be used with our long-selling torque detectors SS/DD series and high accuracy, high response type TH series. Since all signals are digitally processed, torque measurement can be performed with great stability, reproducibility and linearity.
-
Analog Devices Inc.
Analog Devices’ ADE energy measurement ICs address the challenges of next-generation smart meter architectures and are ideal for measuring active energy (kWh), apparent energy (kVA), reactive energy (kVAR), rms, and power quality with the highest accuracy in single phase and polyphase revenue meters, industrial instruments, and energy monitoring applications. ADI’s ADE energy measurement ICs combine analog-to-digital converters with fixed-function digital signal processors to perform critical measurements, while providing unparalleled functionality and ease of use.
-
LS3300 -
Yokogawa Test & Measurement Corp.
The LS3300 is an AC signal generator capable of outputting both current and voltage simultaneously, thus allowing it to calibrate power meters. Providing output ranges of 10mV-1250V, and 0.3 mA to 62.5 A, and upto 78.125 kW, the unit is capable of calibrating up to 0.15 % Class Power meters. New features on the LS3300 include a high definition LCD display, a vector diagram, and the ability to synchronize up to three units to emulate anything from single phase two wire to three phase four wire systems.
